Droplet-shaped wave

100 kW Goldschmidt alternator at Eilvese, Germany. The 250 HP DC electric motor (right), turned the 3 ft. diameter, 5 ton rotor (center), at 4000 RPM. The rotor had 360 poles, and the fundamental frequency of the alternator was 24 kHz. Complicated "reflector" circuits (capacitor banks against walls) forced the machine to produce alternating current at four times this frequency, 96 kHz. The transmitter was used for transatlantic radiotelegraphy traffic, exchanging Morse code messages with a similar Goldschmidt station at Tuckerton, New Jersey, USA. During World War 1 it was Germany's main communication channel to the outside world, and was used for diplomatic negotiations leading to the Armistice.

The Goldschmidt alternator or reflector alternator, invented in 1908 by German engineer Rudolph Goldschmidt, was a rotating machine which generated radio frequency alternating current and was used as a radio transmitter. Radio alternators like the Goldschmidt were some of the first continuous wave radio transmitters. Like the similar Alexanderson alternator, it was used briefly around World War 1 in a few high power longwave radio stations to transmit transoceanic radiotelegraphy traffic, until the 1920s when it was made obsolete by vacuum tube transmitters.

Description

Although the device was a radio transmitter, it resembled an electric generator used to produce electric power in a power plant. Like other generators it consisted of a rotor, several feet in diameter, wound with coils of wire, which rotated inside a stationary frame called a stator which had its own coils. The interaction between the magnetic fields of the rotor and stator produced radio frequency currents in the windings, which were picked off by rotating contacts on the shaft and applied to the antenna.

A high frequency alternator differed from an ordinary electric generator in that to produce radio frequency current it rotated much faster, and had many more magnetic "poles" on the rotor and stator, usually 300 to 600. The Goldschmidt alternator was turned by a powerful DC electric motor attached to the shaft, through a geartrain which increased the motor's speed to several thousand RPM. The advantage of the Goldschmidt design was that by using external "reflector" capacitor banks that increased the frequency of the current to a multiple (harmonic) of the alternator's rotation speed, it allowed the rotation speed to be kept lower, simplifying the mechanical design. Goldschmidt transmitters operated at longwave (LF and VLF) frequencies of about 20 to 100 kHz.

Goldschmidt machines were used from 1910 to about 1930 as the transmitters in a few central "superpower" longwave radio stations, which were employed not for broadcasting but for wireless telegraphy, to transmit telegraph messages in Morse code to similar stations in other nations all over the world. Only alternator transmitters like the Goldschmidt and Alexanderson could produce the high powers (50 to 200 kW) necessary to communicate reliably at transoceanic distances. The Goldschmidt was a less widely used design, mostly used in European stations. The stations themselves resembled a utility powerhouse, with the humming alternators connected through huge loading coils to enormous wire antenna systems stretching for miles, suspended on steel towers.

History

12.5 kW Goldschmidt alternator installed in 1910 at a wireless station in Eberswald, Germany. It had an output power of 12.5 kW at a frequency of 30 kHz, or 8 to 10 kW at 60 kHz. It consists of a DC electric motor (left) driving the alternator (right) through a gearbox (center) which steps up the rotation speed.

Around 1900 it was realized that the existing technology for generating radio waves, the spark-gap transmitter, was inadequate because it generated damped waves. Efforts were made to design a transmitter that would generate sinusoidal continuous waves. In 1891 Frederick Trouton pointed out that if an AC generator (alternator), which produces alternating current, could be built to run fast enough, with enough poles, it would generate high frequency alternating current in the radio range. If P is the number of pole pairs and U is the rotational speed in revolutions per second, the frequency f in hertz of the current produced by an alternator is

$f=PU\,$

A number of researchers such as Nikola Tesla had tried building radio alternators, but they had been unable to produce frequencies above 10,000 Hz due to the engineering problems of building a machine with many poles that would rotate fast enough. In 1906 Reginald Fessenden and Ernst Alexanderson at General Electric began to solve the problems and build alternators which could produce frequencies of ~100 kHz. However the Alexanderson alternator ran at extremely high speeds; to reach 100 kHz with a 300 pole rotor required a rotor speed of 20,000 RPM, which strained the engineering ability of the time. It was 1916 before Alexanderson machines achieved the high power needed for transatlantic wireless communication.

In 1908 Westinghouse engineer Rudolph Goldschmidt devised an intricate method to enable an alternator to generate high frequency without requiring excessive speeds. His technique was to exploit resonance to use the alternator as a frequency multiplier as well as a generator. By attaching tuned circuits called "reflector" circuits to the stator and rotor windings, Goldschmidt found that an alternator could be made to produce output power at a multiple (harmonic) of its fundamental rotational frequency PU. The output frequency of the Goldschmidt alternator was

$f=NPU\,$

where N was a small integer. N was limited to 4 in most practical machines, as losses due to leakage flux increased rapidly with increasing N. Thus a 100 kHz Goldschmidt machine with 300 poles would require a rotor speed of only 5000 RPM, one-fourth that of an equivalent Alexanderson machine. 80% efficiency could be achieved, but in order to keep the leakage flux low enough to achieve this the machine required a very narrow clearance of 0.8 mm between the stator and rotor, which could weigh 5 tons and be moving at a peripheral speed of 200 meters per second. Another challenge was that to reduce hysteresis losses in the iron rotor at radio frequencies, it had to be made of very thin foil laminations, .05 mm (.002 in) thick, separated by paper sheets, so the rotor was more than 1/3 paper. No rotor of this construction had ever been used in a large machine. The limit of output frequency for Goldschmidt alternators, as well as other alternator technologies, was about 200 kHz.

The machine was developed and manufactured by the German company Hochfrequenz-Maschinen Aktiengesellschaft für Drahtlose Telegraphie ("Homag") and was mostly used in Europe. The Goldschmidt machine, like the Alexanderson and other alternator transmitters, was used mainly for high power longwave stations that transmitted radiotelegraphy messages, both commercial stations that handled private traffic, and naval stations that kept governments in touch with their colonies and naval fleets. The first Goldschmidt machine in the UK, a 12 kW, 60 kHz transmitter was installed at Stough in 1912. A 100 kW, 400 pole unit was put into operation at Neustadt-am-Ruebenberger, Germany, and the first machine in the USA was a similar 120 kW, 400 pole, 40.5 kHz unit at Tuckerton, New Jersey. A 250 kW unit installed at Laeken, Belgium in 1913 to communicate with Belgium's African colonies was destroyed by the Germans in 1914. World war 1 brought home the importance of radio communication, as nations realized that without it, they could easily be isolated by enemies cutting their submarine telegraph cables. This precipitated a building boom of large transcontinental radio stations.

The heyday of the big alternator radio transmitters was around 1920. They were superseded during the next decade by cheaper and smaller vacuum tube transmitters, made possible by the invention of the Audion (triode) tube in 1906 by Lee De Forest, and the feedback oscillator circuit in 1912 by Edwin Armstrong and Alexander Meissner. By 1921 the Marconi Co. had installed 100 kW vacuum tube transmitters for transatlantic message traffic at its stations at Carnarvon, Wales and Glace Bay, Newfoundland. Alternator transmitters were used through the 1930s.

Other radio alternators

The Goldschmidt alternator was one of several types of rotating "radio frequency alternator" machines used as radio transmitters during the first two decades of the 20th century. Alternator transmitters produced a "cleaner" signal with less harmonics than their main competitor, the Poulsen arc transmitter so they were used in the highest power telegraphy stations. The machines differed in how they solved the fundamental problem of producing high frequencies without exceeding the mechanical capabilities of rotating machines:

• Alexanderson alternator - This machine had a rotor that turned at a high enough speed to produce the radio frequency signal directly. It was probably the most widely used type. However the high rotational speed required, around 20,000 RPM, made the mechanical design very complicated, requiring a water-cooled stator and forced oil lubrication. The Alexanderson alternator took 10 years to develop and was very expensive. It was produced by General Electric and used by its subsidiary RCA and the US Navy.
• Goldschmidt alternator - As described, the Goldschmidt design used a rotor that turned at a lower speed, 3000 to 5000 RPM, and then used the rotor to multiply the fundamental frequency several times to produce the radio output at a harmonic of the fundamental frequency.
• Bethenod-Latour alternator - This machine had two or three rotors on the same shaft, with the rotors advanced in angle so the fundamental alternating current signals they produced had different phases. The currents from the separate rotors were combined, producing a signal at two or three times the frequency.
• Arco alternator - In this machine the alternator produced its signal at a lower fundamental frequency, and the frequency was multiplied 2 to 4 times in a magnetic amplifier, a nonlinear inductor with a magnetized iron core, which produced a harmonic of the fundamental frequency. This device was developed by Telefunken/AEG.

References

43 year old Petroleum Engineer Harry from Deep River, usually spends time with hobbies and interests like renting movies, property developers in singapore new condominium and vehicle racing. Constantly enjoys going to destinations like Camino Real de Tierra Adentro.